TORK CRAFT

Tork Craft Brush Holder Assembly (33, 34) For TCRH0800 (TCRH0800-SK04) At a Glance: Brush holder assembly covering reference parts (33 and 34) for the Tork Craft TCRH0800. Carbon brushes only work properly when they’re guided straight, held securely, and kept under consistent spring pressure. When the brush holder assembly cracks, heat-distorts, or fills with carbon dust and grime, brushes can stick or wear unevenly—leading to heavy sparking, erratic power and a motor that feels rough and ..

Tork Craft Brush Holder Set (24/25) Service Kit For TCID0850 At a Glance: Replacement brush holder set (parts 24 and 25) for the Tork Craft TCID0850 impact driver Fresh carbon brushes are only half the story—if the brush holders are cracked, worn, or letting the brushes bind, the motor won’t get clean contact and performance can drop fast. The Tork Craft TCID0850-SK08 Brush Holder Set service kit replaces the brush holder components (parts 24 and 25), restoring proper brush alignment and s..

Tork Craft Brush Holder Set (42/44-46) Service Kit For TCID1100 At a Glance: Replacement brush holder set (parts 42 and 44–46) for the Tork Craft TCID1100 motor Carbon brushes can only do their job if they slide freely and stay correctly aligned against the commutator. If the brush holders are cracked, heat-damaged, worn, or packed with carbon dust, brushes can bind or sit skew—causing weak power, intermittent running and excessive sparking. The Tork Craft TCID1100-SK09 Brush Holder Set se..

Tork Craft Brush Holder Set Compl. (39/40/46/47) Service Kit (TCAG0115-SK12) At a Glance: Complete brush holder set (parts 39, 40, 46 & 47) for the Tork Craft TCAG0115 angle grinder Carbon brushes do the dirty work of delivering current into a spinning armature, but they can only do it properly if the brush holders are secure, aligned, and electrically sound. When brush holders crack, loosen, or their springs and seating points wear out, you’ll often see intermittent power, excessive spark..

Tork Craft Brush Holder Set Compl. (44-46/48/49) Service Kit (TCAG0230-SK12) At a Glance: Complete brush holder set (parts 44–46, 48 & 49) for the Tork Craft TCAG0230 angle grinder Carbon brushes can only do their job properly if the brush holders keep them aligned, secure and making consistent contact with the spinning armature. When holders crack, loosen, or the seating/spring action becomes unreliable, you may get intermittent power, excessive sparking, cutting out under load, or a grin..

Tork Craft Brush Pair, Brush Holder & Coil Spring (47–49) For POL06-2G At a Glance: Complete brush, holder and spring kit for the Tork Craft POL06-2G polisher The Tork Craft brush pair, brush holder and coil spring kit (Cat No. POL06-2G-SK04) is a genuine service kit for the Tork Craft POL06-2G 1500W 180mm polisher. Carbon brushes and their springs are wear components – as they shorten or lose tension, you may notice power loss, intermittent running, excess sparking or a burnin..

Solid polishing compound - Grey Application: Grey solid finishing compound For steel, stainless steel, chrome and aluminium The compound should be used on a Sisal buff or stitched buff. A white stitched buff is ideal for cutting into metals. With the correct compound it will remove stretcher strains, orange peel,polishing wheel grit lines, lig..

Solid polishing compound - Red Application: Red solid finishing compound for general purpose The compound should be used on a Sisal buff or stitched buff. A white stitched buff is ideal for cutting into metals. With the correct compound it will remove stretcher strains, orange peel,polishing wheel grit lines, light die marks etc. ..

Buffing pad Buffing pad density: Medium Diameter: Ø100mm Bore: Ø12.5mm Application: The buffing pad is used together with a chuck adaptor spindle supplied with the TC874 polishing kits. Alternatively the TC336 arbor would also fit the buffing pad. How to use the compounds and the buffing pads: The adaptor is used to hold the buffing pad in the drill's chuck. Fasten the correct buffing pad in the adaptor. Make sure the flanges are on both sides of the b..

Buffing pad Buffing pad density: Medium Diameter: Ø150mm Bore: Ø12.5mm Application: The buffing pad is used together with a chuck adaptor spindle supplied with the TC874 polishing kits. Alternatively the TC336 arbor would also fit the buffing pad. How to use the compounds and the buffing pads: The adaptor is used to hold the buffing pad in the drill's chuck. Fasten the correct buffing pad in the adaptor. Make sure the flanges are on both sides of the buf..

Buffing pad Buffing pad density: Firm Diameter: Ø150mm Bore: Ø12.5mm Application: The buffing pad is used together with a chuck adaptor spindle supplied with the TC874 polishing kits. Alternatively the TC336 arbor would also fit the buffing pad. How to use the compounds and the buffing pads: The adaptor is used to hold the buffing pad in the drill's chuck. Fasten the correct buffing pad in the adaptor. Make sure the flanges are on both sides of the buffi..

Buffing wheel kit Buffing wheels in the kit: (x1) Ø100mm Sisal stitched buff (x1) ø100mm denim stitched buff (x1) ø100mm cotton stitched buff Application: Different metals have varying characteristics. To achieve the best possible result, it is essential that the correct compound and polishing buff is selected for the job. The cutting compound should be used on a Sisal buff or stitched buff. A white stitched buff is ideal for cutting into metals. With the correc..