AIRCRAFT

AirCraft Air Stapler Service Kit – End Cap & Air Fitting Kit (For AT0001) (AT0001-SK10) At a Glance: Replacement end cap and air fitting components to restore rear sealing and a secure air connection on the AT0001. If your AT0001 stapler/nailer is leaking air from the rear, or the air inlet connection is starting to feel loose or unreliable, it’s time to service the end cap area. The AirCraft AT0001-SK10 End Cap & Fitting Kit is designed for the AT0001 tool platform and includes the key parts ..

AirCraft Air Stapler / Nailer Service Kit – Gaskets, Piston & O-Rings (18 Gauge) (AT0001-SK02) At a Glance: Complete seal and gasket service kit for AirCraft 18 gauge pneumatic nailers—restores sealing, power, and reliability. Air leaks and weak firing usually don’t mean your nail gun is finished—they often mean the seals are. The AirCraft AT0001-SK02 service kit is designed to refresh your pneumatic nailer’s internals with the key wear parts: gaskets, piston sealing components, and O-rings. B..

AirCraft Air Stapler Service Kit – Main Body (21–22) for AT0002 (AT0002-SK03) At a Glance: Main body service kit for the AirCraft AT0002 air stapler (parts reference 21–22) to restore secure fitment and dependable performance. When a stapler starts losing its “tight and true” feel, the problem often lives in the main body area—wear, impact damage, or fatigue can cause misalignment, inconsistent cycling, or air loss around mating surfaces. The AirCraft AT0002-SK03 service kit is a direct-fit ..

AirCraft Air Stapler Service Kit – Main Body Components (For AT0001) (AT0001-SK03) At a Glance: Main body service kit for the AirCraft AT0001 pneumatic stapler/nailer—designed to restore internal function and reliability. When a pneumatic stapler starts losing efficiency, leaking air, or cycling inconsistently, the problem isn’t always just seals—sometimes the main body components need attention. The AirCraft AT0001-SK03 service kit is intended for main body servicing on the AT0001 tool platfo..

AirCraft Air Stapler Service Kit – Safety Tip Kit (For AT0001) (AT0001-SK06) At a Glance: Replacement contact safety (safety tip) components for the AirCraft AT0001—helps restore safe, correct tool activation. The contact safety tip is one of the most important parts of any pneumatic stapler/nailer—it’s what helps prevent the tool from firing unless it’s correctly pressed against the workpiece. If the safety tip becomes sticky, worn, bent, or unreliable, the tool can misfire, refuse to fire, o..

AirCraft Air Tire Buffer For Roughing Low Areas, Recapping And Tire Scuffing (AT0022) At a Glance: Pneumatic tyre buffer designed for controlled roughing, scuffing and surface preparation—ideal for recapping, patch work and adhesion prep. Tyre repair and recapping work lives or dies on surface preparation. If the rubber isn’t keyed properly, bonding suffers—and the job won’t last. The AirCraft AT0022 Air Tire Buffer is built for the real-world grind: roughing low areas, scuffing tyre surfa..

AIR VALVE BODY FOR SG H827....

Airbrush compressor The compressor is designed for airbrush use. It will switch off when the tank is full and will switch on during use. An in-line filter and water trap is supplied with the 1.7m hose to ensure the media in the airbrush isn&t contaminated with dust or water. The filter needs to be fitted directly under the airbrush. The oil-less piston motor is thermally protected and is maintenance free and runs at a low noise ≤ 50dB. The airbrush compressor is designed for ..

AirCraft Airbrush Finger Rest At a Glance; Replacement finger rest for improved comfort, stability and control while airbrushing Airbrushing is all about tiny movements and consistent control—and your hand position matters more than you’d think. The AirCraft SG-BD-480 Airbrush Finger Rest is a replacement support rest designed for compatible airbrush models, giving your finger a more comfortable reference point while you work. It helps stabilise your grip, improve fine control, and reduce ..

Airbrush holder - fits on an inline regulator Holds up to 2 airbrushes at a time. Unscrew the red plastic locking ring on the top of the inline regulator to fit the airbrush holder. Perfect for airbrush compressors.....